Synthetic Multi-Purpose Grease, NLGI #1
(GLB)
 
Package sizes include:
 |
14-oz. Cartridge |
|
14-oz. Cartridges (case of 10) |
|
14-oz. Cartridges (case of 40) |
|
35-lb. Lug |
|
120-lb. Keg |
|
400-lb. Drum |
PRODUCT
DESCRIPTION
AMSOIL
Synthetic Multi-Purpose Greases are qualified against the
highest grease standards and are designed for multiple
use applications. Composed of premium quality synthetic
base oils and lithium complex thickeners, Multi-Purpose
Greases provide superior film strength, shear resistance,
adhesion properties and mechanical stability, and they
excel in temperature extremes by providing excellent
oxidation stability, high temperature dropping points and
low temperature torque values and pumping capabilities.
AMSOIL Synthetic Multi-Purpose Greases are formulated
with oil soluble extreme-pressure additives for heavy
loads, as well as oxidation and corrosion inhibitors that
impart good oxidation stability and rust
protection.
PERFORMANCE FEATURES
- High dropping point of
500°F+
- Resists thermal and oxidation
degradation
- Excellent water-washout
resistance
- Good low temperature pumpability and
torque values
- Adhesive and shear stable to prevent
squeeze out
Applications or
Requirements
- GLB (#1) ASTM D-4950 (NLGI) Service
GC/LB
- GLB (#1) Cincinnati Milicron P-72
Spec
APPLICATION
RECOMMENDATION
AMSOIL
Synthetic Multi-Purpose Grease grade #1 is recommended in
manual or automatic lubricating systems. NLGI #1 (GLB)
has better mobility and is the preferred choice for
colder applications, automatic lubrication systems with
long pumping runs and gear box applications (where
recommended by manufacturer).
The correct consistency grade of AMSOIL
Synthetic Multi-Purpose Grease is recommended in heavy and
light duty applications found in manufacturing plants,
automobiles, agricultural and construction equipment.
These include, but are not limited to, roller
bearings, plain bearings, thrust bearings, gears, electric
motors, presses, winches, bushings, wheel bearings, chassis
lubrication, universal joints, ball joints, tie-rod ends, and
steering knuckles. AMSOIL Synthetic Multi-Purpose Greases are
suitable for use up to 350 degrees F. When operating at
elevated temperatures, frequent regreasing may be required.
AMSOIL Synthetic Multi-Purpose Greases
are compatible with many other types of greases. However, it is
recommended that when changing greases, the equipment be
cleaned of the old grease when possible or flushed with a
liberal amount of Multi-Purpose Grease while the mechanism is
in operation. Closely monitor the system for any
inconsistencies. Grease compatibility questions should be
referred to your AMSOIL representative or AMSOIL
Inc.
APPLICATION
MAINTENANCE
Maintaining
a clean work environment is important when equipment greasing
is performed. Wipe grease fittings clean prior to injecting
grease to prevent contaminant ingestion. Maintain bearing
housings one-third to one-half full of grease. Do not
over-grease, as excessive heat buildup can result. Supplement
standard grease maintenance by periodically cleaning and
packing housings with fresh grease on an established
maintenance schedule.
Typical Technical
Properties
|
| Synthetic GLB
Grease |
GLB |
NLGI
GC/LB |
| Thickener |
lithium
complex |
NR |
| NLGI consistency
grade |
1 |
NR |
| NLGI performance
grade |
GC-LB |
NR |
| Penetration - ASTM D 217 (25°C
[77°F], 0.1 mm) worked 60 strokes |
310-340 |
220-340
min |
| Dropping point, °F[°C] - ASTM
D2265 |
500
[260] |
428 [220]
min |
| High temperature life, hours -
ASTM D 3527 |
140 |
80
min |
| Oxidation stability, psi - ASTM
D 942 (100 hr/300 hr) |
0/5 |
NR |
| Water washout, percent - ASTM D
1264 |
5.8 |
15
max |
| Rust and corrosion - ASTM D
1743 |
pass |
pass |
| Oil separation, percent loss -
ASTM D 1742 (24 hours, 25°C [77°F] |
3.4 |
6.0
max |
| Leakage, g lost - ASTM D
4290 |
7.8 |
10
max |
| Four ball wear test, mm scar -
ASTM D 2266 |
0.43 |
0.60
max |
| Fretting wear, mg - ASTM D
4170 |
3.5 |
10
max |
|
Four ball EP, kgf - ASTM D
2596
Weld point
Load wear index
|
315
49
|
200 min
30 min
|
| Timken OK load test, lbs - ASTM
D 2509 |
45 |
NR |
| Low temperature torque, N*m -
ASTM D 4693 (-40°C [-40°F]) |
0.50 |
15.5
max |
| LT-37 pumpability, g/min
(60°F/0°F [16°C/-18°C]) |
855/29 |
NR |
| Copper corrosion - ASTM D
4048 |
1B |
NR |
|
Disc brake wheel bearing
specifications
Ford ESA-M1C 198A
Chrysler MS-3701
|
NA
NA
|
NR
NR
|
|
Oil viscosity:
40°C [104°F], cSt
100°C [212°F], cSt
|
151
19.2
|
NR
NR
|
| Flash point, °F[°C] - ASTM
92 |
450[232] |
NR |
| Color |
red |
NR |
| Texture |
smooth with
tack |
NR |
NA: Not
applicable
NR: Not required for NLGI
GC-LB labeling
|
Can't find what you're looking
for? Pick an option below:
This content block is currently not available. Please contact RSS feeds service support team.
| 
